Research Papers - Dept of Computer Systems Engineering

Permanent URI for this collection https://rda.sliit.lk/handle/123456789/1253

Browse

Filters

20194

Advanced Search

Filter by

Settings

Author: search.filters.author.Jayawardena, T. S. SSubject: search.filters.subject.Design

Search Results

Now showing 1 - 4 of 4
  • Thumbnail Image
    PublicationEmbargo
    Design and Analysis of An Anthropomorphic Two-DoF Ankle-Foot Orthosis
    (IEEE, 2019-04-19) Ranaweera, R. K. P. S; Abayasiri, R. A. M; Gopura, R. A. R. C; Jayawardena, T. S. S; Mann, G. K. I
    This paper proposes a two-degrees of freedom passive-dynamic ankle-foot orthosis (AFO). In view of enhancing anatomical conformity, an anthropomorphic design is proposed to minimize mechanical interferences between ankle and orthosis. The biomimetic features such as passive stabilizers and dampeners in the proposed mechanism intrinsically support the ankle and foot to maintain stability and improve shock-absorbing ability. The mobility, ranges of motion, and manipulability measures for the proposed AFO have been investigated using mathematical modeling and simulation approaches. The analysis revealed the effectiveness of the proposed AFO in meeting the complex kinematics of ankle joint compared to the predecessors. Potentially, the proposed AFO can serve as a platform to carry out research and development on robotic orthoses for the lower extremity.
  • Thumbnail Image
    PublicationEmbargo
    Design and fabrication of an automatic tension monitoring and regulation system for needle thread
    (IEEE, 2019-07-03) Randima, L. M. L; Sandaranga, D. M. B. C; Jayawardena, T. S. S; Fernando, E. A. S. K
    A matched needle and bobbin thread tensions is a major requirement of a seam and also to the quality of garment. This paper describes an attempt on the development of an automated needle thread tension regulating system for single needle lock stitch sewing machine. Historically, several experiments have been carried out to measure the thread tensions of both needle thread and bobbin thread of a lock stitch machine. However, no evident in favour of the development of a device to adjust the needle thread tension automatically. Despite a cyclic variation of the needle thread tension, a needle thread regulation system is developed to maintain an average needle tension during the cycle at a predetermined level. The developed system can be installed on an existing single needle lock stitch machine and capable of maintaining the required correct thread tension profile for sewing. The needle thread tension regulation system is a closed loop system and with a load cell as a sensing device and a geared DC motor adjusts the compression of the spring of the thread tensioner. A visual display of thread tension is indicated on a 16X4 LCD display and the required needle thread tension is set by 4x4 keypad. An Arduino board controls the electronic equipment in the system.
  • Thumbnail Image
    PublicationEmbargo
    Design and Analysis of An Anthropomorphic Two-DoF Ankle-Foot Orthosis
    (IEEE, 2019-04-19) Ranaweera, R. K. P. S; Abayasiri, R. A. M; Gopura, R. A. R. C; Jayawardena, T. S. S; Mann, G. K. I
    This paper proposes a two-degrees of freedom passive-dynamic ankle-foot orthosis (AFO). In view of enhancing anatomical conformity, an anthropomorphic design is proposed to minimize mechanical interferences between ankle and orthosis. The biomimetic features such as passive stabilizers and dampeners in the proposed mechanism intrinsically support the ankle and foot to maintain stability and improve shock-absorbing ability. The mobility, ranges of motion, and manipulability measures for the proposed AFO have been investigated using mathematical modeling and simulation approaches. The analysis revealed the effectiveness of the proposed AFO in meeting the complex kinematics of ankle joint compared to the predecessors. Potentially, the proposed AFO can serve as a platform to carry out research and development on robotic orthoses for the lower extremity.
  • Thumbnail Image
    PublicationEmbargo
    Design and fabrication of an automatic tension monitoring and regulation system for needle thread
    (IEEE, 2019-07-21) Randima, L. M. L; Sandaranga, D. M. B. C; Jayawardena, T. S. S; Fernando, E. A. S. K
    A matched needle and bobbin thread tensions is a major requirement of a seam and also to the quality of garment. This paper describes an attempt on the development of an automated needle thread tension regulating system for single needle lock stitch sewing machine. Historically, several experiments have been carried out to measure the thread tensions of both needle thread and bobbin thread of a lock stitch machine. However, no evident in favour of the development of a device to adjust the needle thread tension automatically. Despite a cyclic variation of the needle thread tension, a needle thread regulation system is developed to maintain an average needle tension during the cycle at a predetermined level. The developed system can be installed on an existing single needle lock stitch machine and capable of maintaining the required correct thread tension profile for sewing. The needle thread tension regulation system is a closed loop system and with a load cell as a sensing device and a geared DC motor adjusts the compression of the spring of the thread tensioner. A visual display of thread tension is indicated on a 16X4 LCD display and the required needle thread tension is set by 4x4 keypad. An Arduino board controls the electronic equipment in the system.