Browsing by Author "Thambiliyagodage, C"

Now showing 1 - 20 of 27

Open Access
Antibacterial Activity of Cu Decorated TiO2 Nanorods
(Faculty of Humanities and Sciences, SLIIT, 2023-11-01) Nilaweera, G; Thambiliyagodage, C; Jayanetti, M; Liyanaarachchi, H
Global public health is seriously threatened by the spread of infectious illnesses in general, particularly by the appearance of bacterial strains that are resistant to antibiotics. New antibacterial drugs are likely a result of recent developments in the field of nanobiotechnologies, particularly the ability to make metal oxide nanomaterials with specific morphologies. Using antibiotics for a long time period will show antibiotic resistance in host cells, which means the drug does not kill the pathogen anymore. As a solution to this problem, nanoparticles can be used. Researchers may find nanoparticles with high antibacterial activity which can kill the pathogen. This research shows the antibacterial activity of Cu decorated TiO2 nanoparticles against Klebsiella pneumoniae. In here the nanoparticles were synthesized in three weight ratios with TiO2 and CuO using hydrothermal method. Pure CuO and TiO2 were synthesized as controls. Then antibacterial activity was checked by the well diffusion method. After incubation the inhibition zones were measured, and the results were recorded. The antibacterial effect can be determined with the size of the inhibition zone. The synthesized nanoparticles were characterized using XRD to analyze physical properties such as phase composition, crystal structure. The value for inhibition zone of the best performing sample which the sample concentration is 40mg/ml is 13.17±1.53 mm which contains TiO2 : CuO (1:2) weight ratio. Therefore it can be determined that the best performing sample which has the highest antibacterial activity against Klebsiella pneumoniae is G3 which contains TiO2 : CuO (1:2) weight ratio.
Open Access
Antibacterial Activity of Zn Decorated TiO2 Nanocomposites
(Faculty of Humanities and Sciences, SLIIT, 2023-11-01) Kumarasinghe, N.M.A,; Thambiliyagodage, C; Jayanetti, M; Liyanaarachchi, H
Bacterial infections have a significant public health impact. Infections are caused by bacteria in animals, plants as well as humans. Pathogenic bacteria can produce toxins, which are chemical poisons that interfere with cell function such as digestion of normal human enzymes, evasion of infection-fighting white blood cells, and immune clearance. Antibiotic prophylaxis is used to prevent bacterial infection. Antibiotic resistance is one of the most serious concerns in world health. Antibacterial nanoparticles are one possible answer to antimicrobial resistance. These nanomaterials not only kill antibiotic-resistant bacteria through various modes of action but, they can also be employed in conjunction with existing clinically relevant antibiotics to help overcome antimicrobial resistance mechanisms. In this study, anodized titanium dioxide (TiO2) nanorods were treated hydrothermally with zinc oxide (ZnO) nanoparticles to give titanium (Ti) antibacterial properties. The antibacterial activity of synthesized samples was investigated by Agar Well Diffusion method at 40 mg/ml concentration, against gram negative Klebsiella pneumoniae. To determine the antibacterial activity, the diameter of the zone of inhibition was measured, and the resulting data were statistically analyzed. Zn/TiO2 nano particles were characterized by using X-ray diffraction (XRD) Analysis.
Embargo
Assessing the Efficacy of Machine Learning Algorithms in Predicting Critical Properties of Gold Nanoparticles for Pharmaceutical Applications
(Springer Nature Link, 2025-07-08) Fernando, H; Mohottala, S; Jayanetti, M; Thambiliyagodage, C
Au nanoparticles are increasingly used in pharmaceuticals, but their synthesis is costly and time-intensive. Machine Learning can help optimize this process. In this research, eight distinct Machine Learning models were implemented and optimized on a dataset comprising 3000 records of gold nanoparticles. The performance of these models was assessed using four accuracy metrics and the time required for training and inference. The results are promising, with all seven models demonstrating high accuracy and low time requirements. Notably, the XGBoost and Artificial Neural Network models exhibited exceptional performance, with Mean Squared Error values of 0.0235 and 0.0098, Mean Absolute Error values of 0.1021 and 0.0674, Mean Absolute Percentage Deviation values of 0.4945 and 0.3590, R2 scores of 0.9995 and 0.9998, and inference times of 0.0029 and 0.4299 s, respectively. The Explainable Artificial Intelligence analysis of the resulting models revealed some interesting insights into how the models make the predictions and what factors heavily contribute to the nanoparticle AVG_R, allowing chemists to optimize the synthesis for gold nanoparticles better. The key contributions of the research include the design and development of eight Machine Learning models using industry-standard frameworks, the training, tuning, and evaluation of these eight models using five different metrics, and further assessment of these trained models using Explainable Artificial Intelligence. The findings indicate a substantial potential for applying neural networks in the design phase of nanoparticle synthesis, which could lead to significant reductions in both the time and cost required for synthesizing Au nanoparticles for pharmaceutical applications.
Embargo
Assessing the Efficacy of Machine Learning Algorithms in Predicting Critical Properties of Gold Nanoparticles for Pharmaceutical Applications
(Springer, 2025-07-08) Fernando, H; Mohottala, S; Jayanetti, M; Thambiliyagodage, C
Au nanoparticles are increasingly used in pharmaceuticals, but their synthesis is costly and time-intensive. Machine Learning can help optimize this process. In this research, eight distinct Machine Learning models were implemented and optimized on a dataset comprising 3000 records of gold nanoparticles. The performance of these models was assessed using four accuracy metrics and the time required for training and inference. The results are promising, with all seven models demonstrating high accuracy and low time requirements. Notably, the XGBoost and Artificial Neural Network models exhibited exceptional performance, with Mean Squared Error values of 0.0235 and 0.0098, Mean Absolute Error values of 0.1021 and 0.0674, Mean Absolute Percentage Deviation values of 0.4945 and 0.3590, R2 scores of 0.9995 and 0.9998, and inference times of 0.0029 and 0.4299 s, respectively. The Explainable Artificial Intelligence analysis of the resulting models revealed some interesting insights into how the models make the predictions and what factors heavily contribute to the nanoparticle AVG_R, allowing chemists to optimize the synthesis for gold nanoparticles better. The key contributions of the research include the design and development of eight Machine Learning models using industry-standard frameworks, the training, tuning, and evaluation of these eight models using five different metrics, and further assessment of these trained models using Explainable Artificial Intelligence. The findings indicate a substantial potential for applying neural networks in the design phase of nanoparticle synthesis, which could lead to significant reductions in both the time and cost required for synthesizing Au nanoparticles for pharmaceutical applications.
Open Access
Development of Silica-Copper Nanocomposite for Water Purification
(SLIIT, 2022-02-11) Angappan, S; Karunaratne, M; Thambiliyagodage, C
Water pollution is one of the serious concerns across the world at the moment. Industrial wastewater significantly contributes to the negative impacts caused by water pollution. Textile industries discharge large amounts of effluents into water streams with little or no treatment of the discharge because wastewater treatment is an expensive process. Thus, there exists a need for a cheap and effective way to treat textile effluent that contains dyes before being discharged. A high purity silica-based Nano-adsorbent was synthesized by using rice husk as the commercially available main cheap precursor. Copper-loaded silica nanoparticles were successfully functionalized with 3-aminopropyl triethoxysilane (APTES) via the sol-gel pathway to enhance the adsorption performance of organic dyes from textile effluent. The performance of produced Nano-adsorbent was evaluated by using methylene blue as waste adsorbate. As synthesized nanomaterial was characterized by X-Ray Diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy, the XRD results confirmed the presence of silicon dioxide (SiO2) and paramelaconite (Cu4O3) as predicted. The FTIR confirmed the presence of Si–O stretching, N-H bending, C–H stretching, Cu–O stretching and O–H bending vibrations thereby suggesting the presence of SiO2, NH2 groups, CH2, Cu4O3 and physisorbed H2O. The optimum conditions for pH and adsorbent dosage were successfully evaluated for the adsorption process. The optimum pH at which the nanomaterial performed best was at pH 4. The optimum mass of the adsorbent that gave maximum adsorption performance was 20 mg. Kinetic studies revealed that the experimented data was in better correlation with pseudo-second-order kinetics. The outcome of this project would be of interest to textile industries looking for a cheap and effective way to treat textile wastewater
Embargo
Effect of Co-pollutants on the Photocatalytic Activity of Fe doped ZnO Nanoparticles on the Degradation of Methylene Blue
(IEEE, 2022-07-18) Thambiliyagodage, C; Lokuge, N
ZnO nanoparticles and Fe doped ZnO nanoparticles with varying Fe concentrations as 0.025, 0.05, 0.075, and 0.1% respective to Zn, was successfully synthesized by the sol-gel method. Synthesized nanoparticles were characterized by X-ray diffractometry (XRD) and Raman spectroscopy. As revealed by both studies Fe has successfully doped to ZnO without causing any lattice distortions. Synthesized catalysts were photocatalytically active in degrading methylene blue under sunlight. The effect of co-pollutants; Rhodamine B, Pb 2+ , PO43− and S2O32− on the rate of photodegradation was studied and it was found that Rhodamine B, Pb 2+ , and PO43− reduce the rate and S2O32− increases the rate of photodegradation.
Open Access
Efficient photocatalysis of carbon coupled TiO2 to degrade pollutants in wastewater – A review
(Elsevier, 2022-08-27) Thambiliyagodage, C
Water pollution caused by human activities is a monumental problem that the world is facing today. The use of polluted water for domestic, industrial, and agricultural applications creates severe hazardous issues. Therefore, decontamination of polluted water is greatly important. The advanced oxidation process is preferred to purify contaminated water as the pollutants are completely degraded to harmless products. TiO2 is the most widely researched photocatalyst due to its chemical stability, low cost and eco-friendliness. However, the use of TiO2 is limited as it is only sensitive to UV range due to its high band gap (3.0 eV for rutile) and the possible electron-hole pair recombination. TiO2 has been coupled with carbon-based materials to enhance photocatalytic activity by enhancing charge separation and visible light absorption. This review summarizes the recent use of TiO2 coupled to activated carbon, carbon nanotubes, graphene derivatives, and g-C3N4 to degrade different pollutants found in water including dyes, pesticides, pharmaceuticals, phenols and heavy metals. The advantages and disadvantages of using each carbon-based material are discussed. Further, the challenges and opportunities associated with all the materials are presented. Finally, recommendations and possible future outlooks are briefed in this review.
Open Access
Efficient photocatalysis of Cu doped TiO2/g-C3N4 for the photodegradation of methylene blue
(Elsevier, 2023-03-06) Liyanaarachchi, H; Thambiliyagodage, C; Liyanaarachchi, C; Samarakoon, U
The release of dyes into normal water reservoirs has become a tremendous environmental problem and the development of methods to remove such dyes is essential. A novel photocatalyst was fabricated in which Cu doped to TiO2 was coupled with g-C3N4 (Cu-TiO2/g-C3N4) in different weight percentages as 10, 30 and 50%, hydrothermally. Pure TiO2 consisted of both Anatase and Rutile phases where slight lattice distortions were observed in the Cu-doped TiO2 as evidenced by the XRD and Raman analysis. Cu was present at 1.7% by weight respective to TiO2 according to the XRF analysis. Spherical and irregularly shaped aggregated Cu-doped TiO2 nanoparticles in the range of 15–55 nm were heterogeneously distributed on the g-C3N4 matrix as observed by TEM and SEM. The band gap of TiO2 (3.0 eV) was reduced to 2.67 upon doping with Cu. The band gap of g-C3N4 was found to be 2.81 eV and that of Cu-TiO2/g-C3N4 in different weight percentages were in the range of 2.82 to 2.88 eV. Synthesized photocatalysts were tested on the ability to degrade methylene blue under UV and Visible light. Cu-TiO2/50% g-C3N4 showed the highest rate constant (4.4 × 10-3 min−1) which is 5 and 9.8 times greater than TiO2 and g-C3N4, respectively. The rate constant decreased with the introduction of EDTA and Isopropyl alcohol as they scavenge holes and hydroxyl radicals, respectively. The photocatalytic activity of all the nanomaterials increased with the increasing concentration of persulfate due to the increasing concentration of SO4●- and OH● produced. Synthesized nanomaterials effectively adsorb methylene blue under dark conditions following the pseudo-second-order kinetics suggesting that methylene blue molecules were chemisorbed to the adsorbents. The adsorption rate constant resulting in the best-performing photocatalyst was 0.122 g mg−1 min−1. Hence, it is evident that Cu-TiO2/g-C3N4 can effectively degrade methylene blue.
Open Access
Efficient Visible-Light Photocatalysis and Antibacterial Activity of TiO2-Fe3C-Fe-Fe3O4/Graphitic Carbon Composites Fabricated by Catalytic Graphitization of Sucrose Using Natural Ilmenite
(American Chemical Society, 2022-07-26) Thambiliyagodage, C; Usgodaarachchi, L; Jayanetti, M; Liyanaarachchi, C; Kandanapitiye, M; Vigneswaran, S
Dyes in wastewater are a serious problem that needs to be resolved. Adsorption coupled photocatalysis is an innovative technique used to remove dyes from contaminated water. Novel composites of TiO2-Fe3C-Fe-Fe3O4dispersed on graphitic carbon were fabricated using natural ilmenite sand as the source of iron and titanium, and sucrose as the carbon source, which were available at no cost. Synthesized composites were characterized by X-ray diffractometry (XRD), Raman spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray fluorescence spectroscopy (XRF), and diffuse reflectance UV-visible spectroscopy (DRS). Arrangement of nanoribbons of graphitic carbon with respect to the nanomaterials was observed in TEM images, revealing the occurrence of catalytic graphitization. Variations in the intensity ratio (ID/IG), Laand LD, calculated from data obtained from Raman spectroscopy suggested that the level of graphitization increased with an increased loading of the catalysts. SEM images show the immobilization of nanoplate microballs and nanoparticles on the graphitic carbon matrix. The catalyst surface consists of Fe3+and Ti4+as the metal species, with V, Mn, and Zr being the main impurities. According to DRS spectra, the synthesized composites absorb light in the visible region efficiently. Fabricated composites effectively adsorb methylene blue via π-πinteractions, with the absorption capacities ranging from 21.18 to 45.87 mg/g. They were effective in photodegrading methylene blue under sunlight, where the rate constants varied in the 0.003-0.007 min-1range. Photogenerated electrons produced by photocatalysts captured by graphitic carbon produce O2•-radicals, while holes generate OH•radicals, which effectively degrade methylene blue molecules. TiO2-Fe3C-Fe-Fe3O4/graphitic carbon composites inhibited the growth of Escherichia coli (69%) and Staphylococcus aureus (92%) under visible light. Synthesized novel composites using natural materials comprise an ecofriendly, cost-effective solution to remove dyes, and they were effective in inhibiting the growth of Gram-negative and Gram-positive bacteria.
Open Access
Fabrication of dual Z-scheme g-C3N4/Fe2TiO5/Fe2O3 ternary nanocomposite using natural ilmenite for efficient photocatalysis and photosterilization under visible light
(Elsevier, 2022-11-11) Thambiliyagodage, C; Liyanaarachchi, H; Kumar, A; Jayanetti, M; Usgodaarachchi, L; Lansakara, B
The advanced oxidation process is a prominent method available to remove dyes released to normal water reservoirs to alleviate water scarcity. We report the fabrication of novel g-C3N4/Fe2TiO5/Fe2O3 using natural ilmenite sand as the precursor of the metallic semi-conductors exploration of a heterostructure for photodegradation of methylene blue under sunlight. Ternary composites were synthesized by varying g-C3N4 with respect to Fe2TiO5/Fe2O3 and varying Fe2TiO5/Fe2O3 with respect to g-C3N4 where the varying component was varied as 8, 24 and 40%, respect to the constant material. The hybridization of the three semi-conductors has been confirmed by the microscopic, chemical, and structural analyses. X-ray diffraction patterns show the presence of all three g-C3N4, Fe2TiO5 and α-Fe2O3 while the transmission electronic microscopic and scanning electronic microscopic images show the heterogeneous distribution of the metal oxide nanoparticles on g-C3N4 matrix forming the composite. HRTEM images further reveal the junction of Fe2TiO5 and α-Fe2O3. X-ray photoelectron spectra show the existence of s-triazine and heptazine rings in the composites with Fe3+ and Ti4+ as the only oxidation states of Fe and Ti. Fe2TiO5/Fe2O3/40% g-C3N4 with bandgap of 2.63 eV calculated by diffuse reflectance UV-Visible spectroscopy showed the highest photocatalytic activity (0.009 min−1) being 1.3 times greater than the Fe2TiO5/Fe2O3 nanoparticles. Enhanced photocatalytic activity over the fabricated composites was observed due to the increased visible light absorption, efficient charge separation and improved charge transportation. g-C3N4 coupled with 40% Fe2TiO5/Fe2O3 showed the highest antibacterial activity against gram-negative E.Coli. The synthesis of dual Z-scheme g-C3N4/Fe2TiO5/Fe2O3 ternary composite provides new sights in developing novel photocatalysts using natural ilmenite sand for environmental applications.
Open Access
Fabrication of Naturally Derived Chitosan and Ilmenite Sand-Based TiO2/Fe2O3/Fe-N-Doped Graphitic Carbon Composite for Photocatalytic Degradation of Methylene Blue under Sunlight
(MDPI, 2023-04-01) Mendis, A; Thambiliyagodage, C; Ekanayake, G; Liyanaarachchi, H; Jayanetti, M; Vigneswaran, S
first_pagesettingsOrder Article Reprints Open AccessArticle Fabrication of Naturally Derived Chitosan and Ilmenite Sand-Based TiO2/Fe2O3/Fe-N-Doped Graphitic Carbon Composite for Photocatalytic Degradation of Methylene Blue under Sunlight by Amavin Mendis 1,Charitha Thambiliyagodage 1,*ORCID,Geethma Ekanayake 1,Heshan Liyanaarachchi 1ORCID,Madara Jayanetti 1 andSaravanamuthu Vigneswaran 2,3,* 1 Faculty of Humanities and Sciences, Sri Lanka Institute of Information Technology, Malabe 10115, Sri Lanka 2 Faculty of Engineering and Information Technology, University of Technology Sydney, P.O. Box 123, Sydney, NSW 2007, Australia 3 Faculty of Sciences & Technology (RealTek), Norwegian University of Life Sciences, P.O. Box N-1432 Ås, Norway * Authors to whom correspondence should be addressed. Molecules 2023, 28(7), 3154; https://doi.org/10.3390/molecules28073154 Received: 15 March 2023 / Revised: 29 March 2023 / Accepted: 30 March 2023 / Published: 1 April 2023 (This article belongs to the Section Materials Chemistry) Download Browse Figures Versions Notes Abstract Fabrication of chitosan and ilmenite sand-based novel photocatalysts through the catalytic graphitization of chitosan is reported. Nanocomposites consisted of TiO2, Fe2O3 and Fe nanoparticles dispersed on a nitrogen-doped graphitic carbon framework. The surface area, pore volume and macropore structure of the carbon matrix is disturbed by the heterogeneously distributed nanoparticles. The extent of graphitization expanded with increasing metal loading as indicated by variation in the ID/IG ratio. The nanomaterial’s surface consists of Fe3+ and Ti4+, and graphitic, pyridinic and pyrrolic nitrogen were found in the carbon matrix. The band gap values of the composites varied in the 2.06–2.26 eV range. The photocatalytic activity of the synthesized nanomaterials was determined, and the highest rate constant for the photodegradation of methylene blue under sunlight was 4.4 × 10−3 min−1, which resulted with 10 mg/L MB and 25 mg of the best-performing catalyst. The rate constant rose with increasing concentrations of persulfate added to the medium. The rate constant greatly diminished with the addition of isopropyl alcohol as it scavenged hydroxyl radicals. The presence of co-pollutants including Pb2+, rhodamine B, PO43− and Cl− curtailed the rate of reaction. The activity reduced with an increasing number of uses of the catalyst.
Open Access
Fabrication of r-GO/GO/α-Fe2O3/Fe2TiO5 Nanocomposite Using Natural Ilmenite and Graphite for Efficient Photocatalysis in Visible Light
(MDPI, 2023-01) Usgodaarachchi, L; Jayanetti, M; Thambiliyagodage, C; Liyanaarachchi, H; Vigneswaran, S
Hematite (α-Fe2O3) and pseudobrookite (Fe2TiO5) suffer from poor charge transport and a high recombination effect under visible light irradiation. This study investigates the design and production of a 2D graphene-like r-GO/GO coupled α-Fe2O3/Fe2TiO5 heterojunction composite with better charge separation. It uses a simple sonochemical and hydrothermal approach followed by L-ascorbic acid chemical reduction pathway. The advantageous band offset of the α-Fe2O3/Fe2TiO5 (TF) nanocomposite between α-Fe2O3 and Fe2TiO5 forms a Type-II heterojunction at the Fe2O3/Fe2TiO5 interface, which efficiently promotes electron-hole separation. Importantly, very corrosive acid leachate resulting from the hydrochloric acid leaching of ilmenite sand, was successfully exploited to fabricate α-Fe2O3/Fe2TiO5 heterojunction. In this paper, a straightforward synthesis strategy was employed to create 2D graphene-like reduced graphene oxide (r-GO) from Ceylon graphite. The two-step process comprises oxidation of graphite to graphene oxide (GO) using the improved Hummer’s method, followed by controlled reduction of GO to r-GO using L-ascorbic acid. Before the reduction of GO to the r-GO, the surface of TF heterojunction was coupled with GO and was allowed for the controlled L-ascorbic acid reduction to yield r-GO/GO/α-Fe2O3/Fe2TiO5 nanocomposite. Under visible light illumination, the photocatalytic performance of the 30% GO/TF loaded composite material greatly improved (1240 Wcm−2). Field emission scanning electron microscopy (FE-SEM) and high-resolution transmission electron microscopy (HR-TEM) examined the morphological characteristics of fabricated composites. X-ray photoelectron spectroscopy (XPS), Raman, X-ray diffraction (XRD), X-ray fluorescence (XRF), and diffuse reflectance spectroscopy (DRS) served to analyze the structural features of the produced composites. © 2022 by the authors.
Open Access
Fabrication of TiO2 Spheres and a Visible Light Active α‑Fe2O3/ TiO2‑Rutile/TiO2‑Anatase Heterogeneous Photocatalyst from Natural Ilmenite
(researchgate.net, 2022-07-26) Usgodaarachchi, L; Thambiliyagodage, C; Wijesekera, R; Vigneswaran, S; Kandanapitiye, M
High-purity (98.8%, TiO2) rutile nanoparticles were successfully synthesized using ilmenite sand as the initial titanium source. This novel synthesis method was cost-effective and straightforward due to the absence of the traditional gravity, magnetic, electrostatic separation, ball milling, and smelting processes. Synthesized TiO2 nanoparticles were 99% pure. Also, highly corrosive environmentally hazardous acid leachate generated during the leaching process of ilmenite sand was effectively converted into a highly efficient visible light active photocatalyst. The prepared photocatalyst system consists of anatase-TiO2/rutile-TiO2/Fe2O3 (TF-800), rutile-TiO2/Fe2TiO5 (TFTO-800), and anatase-TiO2/Fe3O4 (TF-450) nanocomposites, respectively. The pseudo-second-order adsorption rate of the TF-800 ternary nanocomposite was 0.126 g mg–1 min–1 in dark conditions, and a 0.044 min–1 visible light initial photodegradation rate was exhibited. The TFTO-800 binary nanocomposite adsorbed methylene blue (MB) following pseudo-second-order adsorption (0.224 g mg–1 min–1) in the dark, and the rate constant for photodegradation of MB in visible light was 0.006 min–1. The prepared TF-450 nanocomposite did not display excellent adsorptive and photocatalytic performances throughout the experiment period. The synthesized TF-800 and TFTO-800 were able to degrade 93.1 and 49.8% of a 100 mL, 10 ppm MB dye solution within 180 min, respectively.
Open Access
Fe3O4 Chitosan Nanocomposite as a pH-Responsive Delivery System for Enhanced Delivery of Punica Granatum L. Polyphenols
(American Chemical Society, 2025-10-17) Rukshan, R; Rajapaksha, N; Wijayawardana, S; Thambiliyagodage, C; Senevirathne, U; Jayanetti, M; Samarakoon, U
Punica granatum extract (PG), consisting of punicalagin, ellagic acid, and gallic acid, was loaded onto an Fe3O4/Chitosan (Fe3O4@Chi) nanocomposite (Fe3O4@Chi-PG) to enhance pharmacokinetic properties. Fe3O4was synthesized via the coprecipitation method and coupled with chitosan in 2% acetic acid solution via glutaraldehyde cross-linking. The presence of interested polyphenols in the pomegranate extract was confirmed by HPLC analysis, and the extract was post-loaded to the nanocarrier. XRD confirmed the crystallographic orientation of the nanocarrier, and SEM analysis confirmed the successful coupling of Fe3O4onto the chitosan surface during the fabrication of Fe3O4@Chi. BET surface area analysis revealed the presence of micro- and mesopores in the synthesized materials. Significant reduction of the BET surface area and the pore volume of Fe3O4@Chi-PG compared to Fe3O4@Chi suggested the loading of the porous network and surface by PG. The presence of vibrational bands corresponding to the functional groups of the relevant bioactive compounds was confirmed via FT-IR analysis. The IC50values of the nanocomposite for DPPH and egg albumin denaturation assays were 18.69 and 257.69 μg/mL, respectively. The PG encapsulation efficiency of Fe3O4@Chi-PG was reported to be 86.44%. The pH-responsive release of the polyphenols was studied by fitting the release data into five kinetic models, including Korsemeyer–Peppas (KP) and Peppas–Sahlin (PS). The KP and PS models were selected to interpret the release mechanism based on the R2≥ 0.95 value. A combination of Fickian diffusion, relaxation, and swelling dominates the polyphenol release. Quasi-Fickian diffusion is responsible for the release in media with pH 1–6.7, whereas anomalous transport occurs at pH 7.4 (n = 0.46) according to the KP model. Polymer relaxation is the dominant mechanism for the release of bioactive compounds at pH 7.4, as exhibited by R/F > 1. However, the contribution of relaxation to the release of polyphenols at pH 2.5, 4, and 5.5 was negligible according to the parameters (kR= 0). Characteristics of chitosan, including protonation and deprotonation of NH2groups, surface charge of Fe3O4, ionization of COOH and OH groups of the polyphenols, and molecular weight of the active compounds, contributed to the differences in the release behavior.
Embargo
Heterojunction and homojunction engineering on multi-shelled confinement structure for CO2 photoreduction to CH4
(Elsevier B.V., 2025-10-15) Yang, X; Yang, R; Lu, X; Cao, Y; Ye, P; Zhang, L; Li, K; Li, Z; Jiang, Y; Liu, J; Zhou, Y; Eroglu, Z; Thambiliyagodage, C; Wu, B; Metin, Ö; Zhou, Y; Zhu, W
The underdeveloped CO2 photo-reduction solid-gas mode still relies on precious metals to produce CH4. Fine-tuned ingenious structure and morphology with nonprecious metal can enable better performance with lower cost. We have synthesized and modified a TiO2 with a three-stage cavity and a three-shelled layer, loaded with In2S3 flakes only on the outermost layer. The porous hollow multi-shelled structure can give a sequence of gas diffusion from inside to outside or vice versa. Due to the confinement effect, products generated by the core can only be transferred from the inside to the outside in a unidirectional manner. The In2S3/TiO2 catalysts exhibited high performance comparable to that of conventional noble metal catalysts (e.g., Au-Ag-Pt), with a selectivity of up to 98.28 % for CH4 and a rate of 296.87 μmol·g−1·h−1 without using any co-catalyst or sacrificial agent. Systematic fundamental characterization, as well as in situ characterization and DFT calculations show that homo-junctions consisting of two crystalline phases of TiO2 contribute to the production of more *Hads and *CO. Desorbed CO can be captured and catalyzed by the outer shell In2S3/TiO2 S-scheme heterojunction during diffusion for methanation via formaldehyde intermediate. A series of photoelectrochemical characterizations also confirms that the In2S3/TiO2 hetero-junction improves light absorption and charge separation efficiency. This work provides insight into the future rational design of hollow semiconductors for artificial photosynthesis systems and selective solar fuel production.
Open Access
In vitro influence of PEG functionalized ZnO–CuO nanocomposites on bacterial growth
(PubMed ID, 2024-01-14) Thambiliyagodage, C; Jayanetti, M; Liyanaarachchi, H; Ekanayake, G; Mendis, M; Usgodaarachchi, L
Polyethyleneglycol-coated biocompatible CuO–ZnO nanocomposites were fabricated hydrothermally varying Zn:Cu ratios as 1:1, 2:1, and 1:2, and their antibacterial activity was determined through the well diffusion method against the Gram-negative Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae, and the Gram-positive Staphylococcus aureus. The minimum inhibitory concentration and the minimum bactericidal concentration values of the synthesized samples were determined. Subsequently, the time synergy kill assay was performed to elucidate the nature of the overall inhibitory effect against the aforementioned bacterial species. The mean zone of inhibition values for all four samples are presented. The inhibitory effect increased with increasing concentration of the nanocomposite (20, 40 and 60 mg/ml) on all the bacterial species except for S. aureus. According to the MBC/MIC ratio, ZnO was found to be bacteriostatic for E. coli and P. aeruginosa, and bactericidal for S. aureus and K. pneumoniae. Zn:Cu 2:1 was bactericidal on all bacterial species. A bacteriostatic effect was observed on E. coli and P. aeruginosa in the presence of Zn:Cu 1:1 whereas, it showed a bactericidal effect on S. aureus and K. pneumoniae. Zn:Cu 1:2 exhibited a bacteriostatic effect on E. coli while a bactericidal effect was observed for E. coli, P. aeruginosa, and K. pneumoniae. The metal oxide nanocomposites were found to be more sensitive towards the Gram-positive strain than the Gram-negative strains. Further, all the nanocomposites possess anti-oxidant activity as shown by the DPPH assay.
Open Access
In vitro release kinetics of bioactive compounds (gallic acid, ellagic acid, and eugenol) from chitosan polymer and the bioactivity of herb-loaded chitosan–CuO nanocomposites
(Nature Research, 2025-10-13) Ekanayake, G; Wijayawardana, S; Jayanetti, M; Thambiliyagodage, C; Liyanaarachchi, H; Mendis, A
The biological efficacy of nanocomposites comprised of chitosan, CuO nanoparticles, and extracts of Phyllanthus emblica, and Syzygium aromaticum was studied. The study assessed the pH– and ionic strength-responsive controlled release of the bioactive compounds, gallic acid, ellagic acid and eugenol, from the chitosan biopolymer. Release data were fitted into zero-order, first-order, Korsmeyer–Peppas (KP), Peppas–Sahlin (PS), Higuchi, and Hixson–Crowell kinetic models to evaluate the release mechanism. According to KP and PS models (R2 ≥ 0.96), release was governed by quasi-Fickian diffusion (n < 0.43), where the diffusion occurs along with the polymer relaxation and swelling. P.emblica-coated chitosan (PeC) composite exhibited a burst release at acidic media conditions, and a quasi-Fickian diffusion at pH 5.5–7.4. Higher ionic strength caused salting-in effects for PeC in 0.4 M media, resulting in a transiently increased release. In acidic conditions, diffusion-controlled release was observed for S.aromaticum-coated chitosan (SaC) composite, with the optimal release at pH 4 media. Release was facilitated by hydrophobic nanochannels at elevated pH (8.5–10) and ionic strength of 0.5 M NaCl. The PS model’s relaxation contributions were significant at 0.4 M NaCl and 5 mg drug loading. Both composites demonstrated enhanced release at physiological conditions (0.1–0.2 M NaCl, pH 7.4). Sustained release of SaC was achieved in near-neutral/moderate ionic strength media, whereas PeC exhibited sustained release in acid/low ionic strength media. The PeC and SaC composites showed IC50 values of 10.78 µg/mL and 19.27 µg/mL for the DPPH radical scavenging ability, respectively. Recorded IC50 values for the egg albumin denaturation assay were 467 µg/mL and 390.44 µg/mL, respectively. The antibacterial activity against Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae, and Staphylococcus aureus showed maximum inhibition zones of 11.83 ± 0.06 mm (Chitosan: CuO 1:2), 12.67 ± 0.20 mm (1:4), 16.50 ± 0.09 mm (1:4), and 11.83 ± 0.08 mm (4:1), respectively. Among the herbal-coated samples, SaC exhibited the highest activity of 23.67 ± 2.84 mm against E. coli
Open Access
Influence of ageing of graphene oxide on the properties and morphology of cement mortar
(Nature Research, 2025-12-02) Suganthiny,G; Thambiliyagodage, C; Perera, S. V. T. J; Rajapakse, R. K. N. D
Past studies show that Graphene Oxide (GO) enhances the structural properties of cement composites. However, GO reduces its chemical characteristics with ageing. This study determines the effects of the age of commercial and laboratory-produced GO on cementitious composites. The study considered GO of up to 35 weeks of age, and specimens were chemically characterised using various techniques. The ageing effects were evaluated using consistency, initial setting time, compressive strength, splitting tensile strength, and water absorption. The composite’s thermal resistance was also tested. GO was found to have a shelf life of 13 weeks from production to achieve favourable results. The morphology of the cement mortar was studied to determine the reason for the change in performance with GO age. This study confirms that the carbon-to-oxygen ratio (C/O) and the disorder of graphene oxide sheets (ID/IG ratio), along with the number of GO layers, govern the performance of GO-incorporated cement composites. Both ratios increase with GO age. Aged GOs in mortar increased the mean pore radius and reduced the surface area. Mortar samples with aged GOs have ettringite peaks, while early-age GO-containing samples lack ettringite peaks. Despite reduced mechanical performance with age, all mortar samples remained thermally stable at higher temperatures.
Open Access
Influence of Laboratory Synthesized Graphene Oxide on the Morphology and Properties of Cement Mortar
(MDPI, 2023-01) Ganesh, S; Thambiliyagodage, C; Perera, S. V. T. J; Rajapakse, R.K.N.D
The introduction of Graphene Oxide (GO), a nanomaterial, has shown considerable promise in improving the mechanical properties of cement composites. However, the reasons for this improvement are not yet fully understood and demand further research. This study aims to understand the effect of laboratory-produced GO, using Tour’s method, on the mechanical properties and morphology of cement mortar containing GO. The GO was characterized using Fourier-transform infrared spectroscopy, X-ray Photoelectron Spectroscopy (XRD), X-ray powder diffraction, and Raman spectroscopy alongside Scanning electron microscopy (SEM). This study adopted a cement mortar with GO percentages of 0.02, 0.025, 0.03, 0.035, and 0.04 with respect to the weight of the cement. The presence of GO in cement mortar increased the density and decreased the consistency and setting times. At the optimum of 0.03% GO viscous suspension, the mechanical properties such as the 28-day compressive strength, splitting tensile strength, and flexural strength were enhanced by 41%, 83%, and 43%, respectively. In addition, Brunauer–Emmett–Teller analysis indicates an increase in surface area and volume of micropores of GO cement mortar, resulting in a decreased volume of mesopores. The improvement in properties was due to increased nucleation sites, calcium silicate hydrate (CSH) density, and a decreased volume of mesopores.
Embargo
Kinetic study of in vitro release of curcumin from chitosan biopolymer and the evaluation of biological efficacy
(Elsevier B.V., 2024-09) Wijayawardana, S; Thambiliyagodage, C; Jayanetti, M
Sustained release of curcumin from the polymeric carrier system chitosan, a natural biopolymer material derived from chitin originated from natural shrimp shell waste, was studied. Six kinetic models, zero order, first order, Korsmeyer–Peppas (KP), Peppas – Sahlin (PS), Higuchi, and Hixson–Crowell, were applied to study the drug release kinetics. The release mechanism of the drug from the curcumin-chitosan composite was evaluated by changing the pH, ionic strength of the release media, and drug concentration. KP and PS models were selected among the studied models to investigate the drug release mechanism from the chitosan biopolymer based on the R2 values (R2 > 0.99). The model constants m in the PS model and n in the KP model stand for the case II relaxation and Fickian diffusion contribution, respectively. The n being < 0.43 in the KP model suggests that the Fickian diffusion governs the drug release. Furthermore, there is a noticeable difference between the values obtained for model parameters m and n in the PS and KP models, indicating that Case II relaxation and Fickian diffusion play crucial roles in the curcumin release mechanism from chitosan. Polymer relaxation has been proven to play a predominant role in releasing curcumin from the composite at lower ionic strengths and higher pH values. Anti-inflammatory activity was tested using the egg-albumin denaturation assay, and the diphenyl-2-picrylhydrazyl assay was carried out to determine the antioxidant activity of the composite. The composite material showed IC50 values of 0.29 mg/ mL and 1.08 mg/ mL for anti-inflammatory and anti-oxidant activities, respectively. The drug composite has shown antibacterial activity against Pseudomonas aeruginosa, Klebsiella pneumoniae, and Staphylococcus aureus, which are highly effective against S.aureus. The resulting inhibition zones for S.aureus were 13.34 ± 0.34 mm, 16.34 ± 0.60 mm, and 13.34 ± 0.73 mm for 5, 10, and 20 mg/ml concentrations, respectively. The drug composite’s minimum inhibitory concentration/ minimum bactericidal concentration ratio for S.aureus, K. pneumoniae, and P.aeruginosa was greater than 4, suggesting that they cause bacteriostatic effects.